3K Roll Wrapped 100% Carbon Fiber Pipe Glossy Surface 80MM

Product Description

3K Roll Wrapped 100% Carbon Fiber Tube Glossy Surface 80MM Carbon Fiber Tube
 

Carbon fiber has the best combination of high strength, high stiffness, and lightweight. Our carbon fiber tube is as strong as steel, as stiff as aluminum, and lighter than titanium. Carbon fiber tubes can replace metal tubes in many applications. We offer a wide range of tubes to fit your needs.

Carbon Fiber Tube Applications:

• Light Aircraft
• Prototype Aircraft
• Aerospace
• Radar and GPS antennas
• Communication towers
• Stiffening and reinforcing beams
• Wind power
• Autonomous craft
• Unmanned vehicle capture booms
• Underwater equipment
• Telescope housing
• Large telescope truss tubing
• High Altitude Craft
• Robotic arms
• Transport beams
• Measurement devices
• Electronics housing
• Mining equipment
• Performance arts and production
• Oil and Gas down-hole applications
• Printing rollers and guides
• Truss Structures
• Security gates
• Photography and motion picture
• Energy generation
• Manufacturing beams
• Product distribution
• Medical equipment
• Solar Energy
• Fuel Cell housing

​Carbon Fiber Tube Features:

1. High strength and stiffness to weight
2. Excellent resistance to fatigue
3. Dimensional stability: Low CTE (Coefficient of Thermal Expansion)
4. Resistance to corrosion
5. X-Ray transparency
6. Chemical resistivity

Carbon Fiber Tube Specifications:

We have been engaged in the production of fiber materials for more than 20 years and have a strong engineering team. We will formulate complete solutions for customers from multiple perspectives such as product transportation, installation, maintenance, and cost-effectiveness according to the use conditions and performance requirements of the products.

Carbon Fiber Tube Manufacturing Process :

4-Axis braiding is a process in which we braid carbon fibers over a mandrel. The braiding machine stays in one place and an aluminum mandrel traverses inside of the braiding hoop. The layer of braid is then wet-out with epoxy resin at a 2nd stage in the machine. The laminate is then consolidated and cured at 280F.

Braided composite structures offer extreme durability and toughness due to the interlocking fibers and no seams.
If damage does occur, it does not tend to propagate within the structure.

Typically braided carbon tubes have approximately 75% of fibers directly on the axis of the tube. These fibers are continuous fibers from one end of the part to the other. 10 % of the fibers are +/- 45 deg and around 15% are 90 deg (hoop)
We can make some adjustments to the percentages of fiber orientation; however, it is not possible to get high percentages of +/- 45 deg.

The inherent high percentage of fiber on the 0 axis makes a braided tube a very good compression or bending tube.
Because the machine stays in one place and the mandrel traverses, there is no length limitation to the parts that can be built (the building length, oven length, and mandrel lengths are limiting factors, but the process itself is not limited).

We typically braid longer length parts or larger manufacturing runs compared to pre-preg

Braided carbon fiber tubes tend to have more surface ripples and small voids in the laminate. This is not a structural issue but it can be a cosmetic issue and it may have an effect on the OD tolerance of the part.

Examples of some applications for braided tubing

Communications towers, large antenna assemblies, portable antennas, drone wing spars, aircraft structural tubing, sailboat spars, truss tubing, reinforcing tubes, spacer tubes, stiffening tubes, compression struts, GPS towers, high tension cable struts, awning support tubes, structural beams, low interference towers.

Our Service:
 
1. It ensures that a year of quality assurance and 24 hours online customer service.
2. Protection of your sales area, ideas of design, and all your private information.
3. Request for samples is accepted.
4. Drilling and slotting are accepted.
5. We guarantee the products to be manufactured with the finest materials and mature technics.
All tubes can be repaired at no charge if returned to us, postage prepaid, within one year.